My Hobart undercounter will not start when I close the door. What should I check?

First confirm the machine has power and the door is fully latched. A worn door interlock switch is a very common cause, as is a tank that has not filled enough to allow the cycle. We test both, plus the control, on site.

Our Cornelius lake-house dishwasher leaked on its first run back. Why?

Seals and the inlet valve can dry out or stick when a dishwasher sits idle. Sometimes a couple of cycles restore the seal, but an active leak should be stopped and checked before it damages cabinets or the floor below.

Can you fix a dishwasher that does not fit well in an older Davidson kitchen?

We can check the installation, level the unit and look for pinched hoses or door alignment problems. If the opening simply does not suit the model, the technician will tell you plainly.

Hobart Repair

Hobart Dishwasher Repair in Cornelius & Davidson, NC

Hobart dishwasher repair in Cornelius & Davidson, Mecklenburg County. We diagnose first and agree the price before any work.

Same-day appointments when available90-day parts / 30-day labor warrantyAll major brandsPrice confirmed before work

(980) 588-8688

Open 24 hours, 7 days a week

Schedule Your Repair

Service Type

What type of service do you need?

Or call us directly:

(980) 588-8688

90-Day

Parts Warranty

Same Day

Availability

How It Works

Book Online or Call

Tell us the appliance, the brand and what it is doing

Technician Visit

Same-day when the schedule allows

Diagnose & Quote

Price agreed first — no work without your approval

Fix & Test

Repair done, tested before we leave

Related Services

Samsung Dishwasher Repair

LG Dishwasher Repair

Whirlpool Dishwasher Repair

GE Dishwasher Repair

Maytag Dishwasher Repair

Bosch Dishwasher Repair

KitchenAid Dishwasher Repair

Frigidaire Dishwasher Repair

Charlotte, NC & Nearby SC

Ready to schedule your repair?

ProFix Appliance Repair Charlotte — appliance repair across the Charlotte region. Same-day appointments when the schedule allows.

Call (980) 588-8688 Book Online Now

Hobart Dishwashers: What We Check First

Hobart dishwashers in restaurants and bars around Charlotte are mostly undercounter units and door-type machines, with conveyor models in larger kitchens. All of them follow the same rhythm: recirculate heated wash water from a tank through spinning arms, drain or overflow some of it, then hit the rack with a fresh final rinse that sanitizes either by heat or by chemical. A high-temperature machine adds a booster heater to make the rinse water hot enough.

Scale-coated booster element leaving the final rinse below sanitizing temperature
Door interlock switch worn out, stopping cycles midway
Fill solenoid sticking, causing a short tank fill and poor wash
Wash pump seal leaking water onto the dish room floor

The full explanation, including what you can safely check yourself and when repair beats replacement, is in our Hobart dishwasher repair guide.

Fit, Idle Time and Second Dishwashers

Older kitchens near downtown Davidson sometimes have a dishwasher installed in an opening that is a little too narrow or out of level. A door that does not close square lets water past the gasket at the bottom corner, and a drain hose pinched behind the unit slows draining until dirty water sits in the tub.

Seasonal lake homes in Cornelius bring a different pattern. After weeks without use, door seals can dry out and the inlet valve can stick, so the first cycle back may leak or fail to fill. Some larger lake houses also have a second dishwasher at a bar or outdoor kitchen that gets used mainly in summer.

What You Can Check, and the Visit

Shut off power at the breaker, then clean the filter and check that the spray arms spin freely. Run the kitchen tap until the water is hot before starting a cycle. If the unit leaks onto a condo floor, turn off the valve under the sink and stop using it.

We level and test the unit, check the pump, float and inlet valve, and explain the diagnosis and price before work begins. If the opening itself is the root cause, the technician will explain what would fix it. That might be a shim kit, new brackets or a different-width model.